NanoPi M1
The NanoPi M1 is an Allwinner H3 based ARM board designed and released by FriendlyARM for hobbyists, makers and electronic fans. It is only two thirds the size of the Raspberry Pi. It is open source. It works with Ubuntu MATE, Debian and etc.
The NanoPi M1 uses the Allwinner H3 Soc. It integrates Ethernet, IR receiver, video/audio output and supports HDMI and AVOUT. It can be powered via the MicroUSB port
In such a small board it still integrates rich interfaces and ports. Besides the popular HDMI, Ethernet, USB-Host, USB-OTG, DVP camera interface and AVOUT (audio and video) it has an onboard Microphone, IR receiver, a serial debug port and a Raspberry Pi compatible 40 pin GPIO pin header.
Link to purchase:NanoPi M1 – You CANNOT Miss It
- CPU: Allwinner H3, Quad-core Cortex-A7@1.2GHz
- GPU: Mali400MP2@600MHz，Supports OpenGL ES2.0
- DDR3 RAM:512MB/1GB
- Connectivity: 10/100M Ethernet
- Audio: 3.5mm audio jack/Via HDMI
- Microphone: Onboard microphone
- IR Receiver: Onboard IR receiver
- USB Host：Type A, USB 2.0 x 3
- MicroSD Slot x 1
- MicroUSB: for data transmission and power input, OTG
- Video Output: HDMI 1.4 1080P, CVBS
- DVP Camera Interface: 24pin, 0.5mm pitch FPC seat
- Debug Serial Port: 4Pin, 2.54mm pitch pin header
- GPIO: 2.54mm spacing 40pin, compatible with Raspberry Pi's GPIO. It includes UART, SPI, I2C, IO etc
- User Key: Power LED x 1, Reset x 1
- PC Size: 64 x 50mm
- Power Supply: DC 5V/2A
- OS/Software: u-boot，Ubuntu MATE，Debian
Vertical View (Front)
Vertical View (Back)
Dimensional Drawing
Linux
Boot OS from TF CardUbuntu-MATE and Debian
GPIO Pin Spec
| Pin# | Name | Pin# | Name |
| 1 | SYS_3.3V | 2 | VDD_5V |
| 3 | I2C0_SDA | 4 | VDD_5V |
| 5 | I2C0_SCL | 6 | GND |
| 7 | GPIOG11 | 8 | UART1_TX/GPIOG6 |
| 9 | GND | 10 | UART1_RX/GPIOG7 |
| 11 | UART2_TX/GPIOA0 | 12 | PWM1/GPIOA6 |
| 13 | UART2_RTS/GPIOA2 | 14 | GND |
| 15 | UART2_CTS/GPIOA3 | 16 | UART1_RTS/GPIOG8 |
| 17 | SYS_3.3V | 18 | UART1_CTS/GPIOG9 |
| 19 | SPI0_MOSI/GPIOC0 | 20 | GND |
| 21 | SIP0_MISO/GPIOC1 | 22 | UART2_RX/GPIOA1 |
| 23 | SPI0_CLK/GPIOC29 | 24 | SPI0_CS/GPIOC3 |
| 25 | GND | 26 | SPDIF-OUT/GPIOA17 |
| 27 | I2C1_SDA/GPIOA19 | 28 | I2C1_SCL/GPIOA18 |
| 29 | GPIOA20 | 30 | GND |
| 31 | GGPIOA21 | 32 | GPIOA7 |
| 33 | GPIOA8 | 34 | GND |
| 35 | UART3_CTS/SPI1_MISO/GPIOA16 | 36 | UART3_TX/SPI1_CS/GPIOA13 |
| 37 | GPIOA9 | 38 | UART3_RTS/SPI1_MOSI/GPIOA15 |
| 39 | GND | 40 | UART3_RX/SPI1_CLK/GPIOA14 |
Debug Port（UART0）
| Pin# | Name |
| 1 | GND |
| 2 | VDD_5V |
| 3 | UART_TXD0 |
| 4 | UART_RXD0 |
DVP Camera IF Pin Spec
| Pin# | Name |
| 1, 2 | SYS_3.3V |
| 7,9,13,15,24 | DGND |
| 3 | I2C0_SCL |
| 4 | I2C0_SDA |
| 5 | GPIOB14 |
| 6 | GPIOB16 |
| 8,10 | NC |
| 11 | VSYNC |
| 12 | HREF |
| 14 | PCLK |
| 16-23 | Data bit7-0 |
DVP Camera IF Pin Spec
| Pin# | Name | Description |
| 1, 2 | SYS_3.3V | 3.3V power output, to camera modules |
| 7,9,13,15,24 | GND | Gound, 0V |
| 3 | I2C2_SCL | I2C Clock Signal |
| 4 | I2C2_SDA | I2C Data Signal |
| 5 | GPIOE15 | Regular GPIO, control signals output to camera modules |
| 6 | GPIOE14 | Regular GPIO, control signals output to camera modules |
| 8 | MCLK | Clock signals output to camera modules |
| 10 | NC | Not Connected |
| 11 | VSYNC | vertical synchronization to CPU from camera modules |
| 12 | HREF/HSYNC | HREF/HSYNC signal to CPU from camera modules |
| 14 | PCLK | PCLK signal to CPU from camera modules |
| 16-23 | Data bit7-0 | data signals |
- SYS_3.3V: 3.3V power output
- VDD_5V: 5V power input/output. When the external device’s power is greater than the MicroUSB’s the external device is charging the board otherwise the board powers the external device. The input range is 4.7V ~ 5.6V
- All pins are 3.3V and output current is 5mA. It can drive small loads.
- For more details please refer to the document: NanoPi-M1-1603-Schematic.pdf
Please visit our official site: www.friendlyarm.com to place orders .By default we ship via CHINA POST. It takes up to one month for CHINA POST to ship. If you want us to ship via DHL/Fedex/TNT/UPS please email us at sales@friendlyarm.com